Search

AIM MyChron Kart Exhaust Gas Power Valve AIM power valve sensor provides a very accurate indication of the exhaust gas valve* working, measuring its gap in mm. The sensor, which measures valve stroke until 20mm, samples RPM value that opens/closes the valve and all intermediate values too. Data are immediately visible on MyChron4 displa..

AIM MyChron 5 Fuel/Oil 0-160 Bar Pressure Sensor M10 Thread This sensor fits the measurement of oil and fuel pressure up to 160 Bars of pressure. The sensor is sold with a 40 cm cable.AiM MyChron Fuel/Oil 0-160 Bar Pressure Sensor M10 Thread:Manufacturer: AimManufacturer part number: M10 – X05PSA00160B10Electrical End Protocol: 719 Push-InThis..

AIM MyChron Kart Steering Position Sensor With the MyChron Steering Sensor Kit you can compare the amount and the rate of the steering wheel input between drivers or use the information for driving coaching. Did the driver react to a slide, or did he cause the kart to understeer? Measure and log driver steering input with the AiM Steering ..

STEERING WHEEL position sensor – 80cmThis potentiometer sensor measures the position of the steering wheel.Designed for : Box12 / Box4Move...

EXHAUST sensor “K” – 40cm “Professional quality, red label”This K thermocouple technology sensor must be installed on the exhaustRead the explanation on the installation and use of this sensor, the document is in the SUPPORT rubricNote : this sensor must be used with an extension cable ref. A3401 or a hub ref. A2190..

AIM MyChron Kart Accelerator/Brake Pedal Position Sensor Kit This sensor uses a magnet to send kart throttle or brake position data to your MyChron5 or MyChron 4 kart data logger. Easy to connect and program the AiM MyChron Kart pedal Position sensor can give accurate data analysis of brake lock-up, and throttle position VS RPM & La..

PEDAL position sensor – 120cmThis Hall effect sensor measures the position of the brake pedal or the accelerator pedal.Designed for : Box12 / Box4Move...

INFRARED Sensor – 40cmDesigned to detect our the coded infrared beams of the ALFANO transmitter, ref. A4100Note : this article is delivered in the box with the PROIIIevo, ref. A1021..

EXHAUST sensor “K” – 40cm “STANDARD quality, blue label”This K thermocouple technology sensor must be installed on the exhaustRead the explanation on the installation and use of this sensor, the document is in the SUPPORT rubricNote : this sensor must be used with an extension cable ref. A3401 or a hub ref. A2190..

USB cable specially designed for Downloading data of ALFANO6..

SPEED sensor – 195cmNew model (10-03-2019), this speed sensor can be installed directly on the Alfano 6 and PROIIIevo (in the green connector), without the need to use the A2192 (old model) or A2194 Hub.This sensor can be used on the rear axle or on the front wheel of kartingNote : for those who need an extension to install it on another vehicle, u..

WATER sensor “NTC” M10 – 45cmThis NTC sensor technology provided with a metric thread 10mm can be connected either on the cylinder head of the engine if it is equipped with an opening designed for installing this sensor either this sensor can be instal on an aluminium adapter, ref. A261, A262, A263, A264Note : this sensor must be used with an exten..

SPARK PLUG sensor “NTC” – D: 14mm /45cmThis NTC technology sensor in normal version should be installed with a 14mm diameter candle.Warning : it is important to remove the sealing washer of the spark plug before installationNote : this sensor must be used with an extension cable ref. A3301 or a hub ref. A2190..

Designed to detect our magnetic strips installed on the tracksNote : this article is delivered in the box with the PROIIIevo. Option for ALFANO6..

HUB with 2 inputs : SPEED + MAGNETIC – 20cmNew model, this A2194 Hub replaces the old model A2192.This HUB can simultaneously connect a speed sensor A2201 (old model) or A2203 (new model) + a magnetic sensor A1302Note : this HUB is designed to be plugged to the green connector of PROIIIevo, ALFANO6...