AIM MyChron Kart Tire Temperature Sensor KitThis complete AIM Kart Tire Temperature sensor kit covers all 4 tires, easily connects to your MyChron 5 or MyChron 5 2T and is specifically designed to measure the surface temperature of all 4 kart tires, providing important info for chassis tuning, tire exploitation, and driver behavior. The s..

AIM MyChron Brake Pressure Sensor Kit This AIM Brake Pressure Sensor kit allows for precise analysis of braking points, braking technique, and even brake bias calculation.Rather than measuring the position of the brake pedal, this pressure sensors allows for a higher degree of accuracy by measuring actual system pressure.Kit includes: • AiM ..

AIM MyChron Kart Exhaust Gas Power Valve AIM power valve sensor provides a very accurate indication of the exhaust gas valve* working, measuring its gap in mm. The sensor, which measures valve stroke until 20mm, samples RPM value that opens/closes the valve and all intermediate values too. Data are immediately visible on MyChron4 displa..

AIM MyChron 5 Fuel/Oil 0-160 Bar Pressure Sensor M10 Thread This sensor fits the measurement of oil and fuel pressure up to 160 Bars of pressure. The sensor is sold with a 40 cm cable.AiM MyChron Fuel/Oil 0-160 Bar Pressure Sensor M10 Thread:Manufacturer: AimManufacturer part number: M10 – X05PSA00160B10Electrical End Protocol: 719 Push-InThis..

AIM MyChron Kart Steering Position Sensor With the MyChron Steering Sensor Kit you can compare the amount and the rate of the steering wheel input between drivers or use the information for driving coaching. Did the driver react to a slide, or did he cause the kart to understeer? Measure and log driver steering input with the AiM Steering ..

STEERING WHEEL position sensor – 80cmThis potentiometer sensor measures the position of the steering wheel.Designed for : Box12 / Box4Move...

EXHAUST sensor “K” – 40cm “Professional quality, red label”This K thermocouple technology sensor must be installed on the exhaustRead the explanation on the installation and use of this sensor, the document is in the SUPPORT rubricNote : this sensor must be used with an extension cable ref. A3401 or a hub ref. A2190..

AIM MyChron Brake Pressure Sensor This AIM Brake Pressure Sensor kit allows for precise analysis of braking points, braking technique, and even brake bias calculation.Rather than measuring the position of the brake pedal, this pressure sensors allows for a higher degree of accuracy by measuring actual system pressure.You will also need: ..

AIM MyChron Kart Accelerator/Brake Pedal Position Sensor Kit This sensor uses a magnet to send kart throttle or brake position data to your MyChron5 or MyChron 4 kart data logger. Easy to connect and program the AiM MyChron Kart pedal Position sensor can give accurate data analysis of brake lock-up, and throttle position VS RPM & La..

PEDAL position sensor – 120cmThis Hall effect sensor measures the position of the brake pedal or the accelerator pedal.Designed for : Box12 / Box4Move...

INFRARED Sensor – 40cmDesigned to detect our the coded infrared beams of the ALFANO transmitter, ref. A4100Note : this article is delivered in the box with the PROIIIevo, ref. A1021..

EXHAUST sensor “K” – 40cm “STANDARD quality, blue label”This K thermocouple technology sensor must be installed on the exhaustRead the explanation on the installation and use of this sensor, the document is in the SUPPORT rubricNote : this sensor must be used with an extension cable ref. A3401 or a hub ref. A2190..

AIM MyChron Rotax Coolant Temperature Sensor M10This thermoresistive Water Temperature sensor is for use with AiM MyChron3, MyChron4 and MyChron 5 and 2T versions of kart dashes. The sensor has M10 male threads for easy installation in Rotax engines. The sensor lead has a 719 push-on connector, that connects to a 3-pin 712 screw-in a..

AIM MyChron EGT Sensor w/ Patch Cable - 2 PieceAiM EGT Sensor Kit with 719 connector. Install this AiM Mychron 4EGT Thermocouple 150mm (5.90") from the exhaust port to accurately measure temperatures ranging from 0 to 1832° F (up to 1000°C).  This is the exact replacement sensor sent with all Aim MyChron Kits.M5 threads allow for com..

AIM Mychron 5 & 4 EGT Thermocouple Sensor - ICC Pipe (KZ/KF Homologated)AiM EGT Sensor designed for KZ & KF homoligated exhaust pipes. Easily connects with any K-Type (two blade flat yellow) connector and threads onto your KZ or KF homologated exhaust pipes sach as IAME, ROK, DeBei, TM and many others. Install this AiM Mychron 3/4/5 EG..